Spare parts suitable for Toyota Corolla and Sprinter E30 E50 Series

This decal was applied to Toyota vehicles through out the 1970's and early 1980's, and denoted the licenced use of ASCO disc brake technology by Toyota.

Complete your Toyota Restoration in style with this decal that is applied to the brake booster (also known as Servo Unit).

Fitted at the very top of the unit, this decal is most visible immediately when the bonnet (hood) is opened. 

Often the original decal may have been removed ahen the servo unit was reconditioned or when a respray of the engine bay has taken place.

Available only from Toyota Heritage this decal will take your restoration one small step closer towards concourse.

We ship worldwide every week - no problems for international buyers.

Suited to Toyota vehicles using four OEM wheel studs per hub.

Ensure good engineering practice with wheel studs that provide for proper engagement of wheel nuts with these longer than standard M12 1.5 pitch 72mm wheel studs.

Good engineering (safety) practice requires wheel nut engagement of the wheel stud to be the equivalent of the wheel stud diameter - 12mm for all Toyota models.

On a 1.5 pitch this means that your wheel nut must get at least 8 turns to ensure a safe and proper engagement.

Please check with us prior to purchase (This email address is being protected from spambots. You need JavaScript enabled to view it.) if your vehicle has been fitted with aftermarket hubs.

Toyota Heritage's long wheel stud kits provide enough length for proper engagement. Our open ended wheel nuts mean that they may also be used with a wide range of aftermarket and factory mag wheels.

Toyota Heritage offers four different wheel stud kits:

• Kit 1 - Wheel studs only
• Kit 2 - Wheel studs with wheel nuts suited to factory mag wheels
• Kit 3 - Wheel studs with wheel nuts suited to after market mag wheels
• Kit 4 - Wheel studs with wheel nuts suited to factory and after market mag wheels

Application:

Kit 1 (Stud Pack)

• 16 pieces (wheel studs) in the kit
• Perfect for when you have purchased after market mag wheels but you are not getting 8 turns of the wheel nuts the vendor supplied

Kit 2 (Factory Pack)

• 32 pieces in the kit including studs and open-end flat seat wheel nuts with captive washers
• Perfect for use with factory mag weels and using a wheel spacer up to 30mm to create offset to suit your handling set-up

Kit 3 (Aftermarket Pack)

• 32 pieces in the kit including studs and open-end tapered seat wheel nuts
• Perfect for use with almost any aftermarket mag wheel requiring a tapered seat wheel nut

Kit 4 (Track Pack)

• 48 pieces in the kit including studs and open-end tapered seat wheel nuts plus open-end flat seat wheel nuts with captive washers
• Perfect for the person who wants to run factory mag wheels around the streets and then switch to their track day wheels and tyres at the track

• Aftermarket Pack Aftermarket Pack
• Factory Pack Factory Pack
• Track Pack Track Pack
• Stud Pack Stud Pack
•  

Radiator support to bonnet (hood) rubber seal fastener clip pack to suit various Toyota models - Celica, Corolla, Corona, Cressida, Land Cruiser, MR2, Hilux, Starlet and Supra

These clips are used to fasten the rubber strip that sits between the bonnet (hood) underside and top of the radiator support panel to reduce wind and water coming into the under bonnet (hood) area. 

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica

• TA40, TA45, TA41, TA42, TA46, TA47, RA40, RA45, RA55, RA46, RA42 and RA43
• TA60, TA61, AA63, TA62, TA63, TA64, SA60, RA63, RA60, RA6, SA63, RA64 and RA65
• ST160, ST162, AT160, ST163, ST164 and ST165
• ST180, ST184 and ST185
• ST200, ST202, ST203, ST204 and ST205

Toyota Corolla

• All models from KE30 through to ZWE182

 Toyota Corona

• All models from ST140 through to ST215

Toyota Cressida

• All models from MX32 through to RX81

Toyota Hilux and Surf

• All models from LN130 through to VZN185

Toyota Land Cruiser

• All models from BJ60 through HZJ105

Toyota MR2

• AW10 andAW11
• ZZW30

 Toyota Supra

• GA70, JZA70 and MA70
• JZA80

Toyota Starlet

• KP60, KP61

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

Front and rear moulded floor carpet for your third generation E30 or E50 series Toyota Corolla.

Suited to all RHD Toyota Corolla E30 and E50 series built between 1974 to 1981 including KE30, KE35, KE36, KE38, KE50, KE55, TE30, TE31, TE35, TE37 and TE50 our moulded carpets are well fitting and made in Australia to the highest quality and replaces OEM carpets nicely.

NOTE: these carpets do not fit the liftback Corolla variants such as TE50, TE51, TE52 and KE50R.

Available in loop or plush pile and fourteen different colours. Just use the drop down menus to select pile and colour.

NOTE: Colour swatches shown are on plush pile carpet and may differ slightly on loop.

Complete your 'third gen' Toyota Corolla project in style - whether its a retro-ride, drift car, daily driver or restoration project.

Shipping worldwide weekly - no problems for overseas buyers.

• Bark Bark
• Black Black
• Blue Blue
• Brown Brown
• Buckskin Buckskin
• Burgundy Burgundy
• Charcoal Charcoal
• Chevy Chevy
• Ginger Ginger
• Green Green
• Kingfisher Kingfisher
• Red Red
• Slate Slate
• Spindrift Spindrift
•  

Complete your early Toyota restoration project in style with a reproduction Toyota (TEQ) Build Plate for vehicles with original delivery in Japan.

These TEQ Build Plates were fitted in the engine bay of all early model Toyota's built during the period from February 1970 to december 1974. Generally these were used up till December 1974, but this may vary on some models and for some cars sold in January 1975.

We have seen these on Crown, Corolla, Corona, Stout, Publica, and Landcruiser just to name a few models.

You may find that your original plate is missing (these are not a VIN!) as an owner may have removed it for painting of sometimes they have corroded and are no longer legible.

The plate was used to inform the production line workers as to what model engine was to be fitted to the vehicle - part of Toyota's quality program!

Our reproduction part is exacting in every detail. 

The pricing includes having your car's data applied to the plate before we ship it to you.

We ship globally to all countries weekly.

Genuine Eagle brand 8mm ignition leads to suit your Toyota Celica, Toyota Corona or Toyota Carina fitted with an 18RG engine.

Our photo shows each of the boot and tube assemblies specific to this kit that suits the 2TG engines.

Suits 2.0L 2TG DOHC GT1600 (Celica and Carina) and Levin or Trueno (Corolla) models as follows:

• Celica - TA23, TA27, TA28, TA40, TA45, TA60 and TA61
• Carina - TA12, TA17, TA40, TA45 and TA60 
• Corolla - TE21, TE27, TE28, TE37, TE51 and TE71 

General description:

 A premium quality ignition lead set specifically designed as an upmarket replacement for OHC motors fitted with Boot and Tube component technology.

Being Eliminator series, they are fitted with 1300 ohms per metre Ferrite Spiral Core conductor which by induction design delivers peak voltage to the plugs ensuring almost complete combustion for super quick starts and smooth running.

Tested to ISO 3808 Standards.

Features - Boot & Tube Assembly Features*

• Hi-temp Silicone Well Cover boot
• PVT insulator tube insulates plug terminal to prevent high voltage crossover
• Hi-temp Silicone Tip Seal.

Terminal Features

• High Memory spring steel retaining clip for positive terminal locking at all RPM'S.
• Extra long .51mm base offers minimal heat transfer from plug tip to inner conductor. This ensures maximum cable life.
• Triple cable retaining ribs and "W" shaped crimp ensure superior cable retention.

 Cable Features

• Simply "the best" Stainless Steel wound Ferrite coated Spiral Core conductor yields ultra low resistance ensuring peak voltage delivery to the spark plugs.
• High Dielectric Silicone inner jacket.
• Technologically advanced nylon tape adds tensile strength.
• 260°C High Temp. modified Silicone outer jacket ensures complete protection against heat and engine bay contaminants.

Shipping wordlwide weekly - no problems for overseas buyers.

Toyota K engine dual valve springs with Titanium retainers.

Suitable for all K, 3K, 4K and 5K applications. Road, rally, race or drift.

Designed for use in engines with modified camshafts which typically require the engine to spin faster in order to make more power. These springs will better control the valve motion and therefore allow a higher engine RPM before valve bounce occurs (ie the loss of valve control point). These springs also allow camshafts to have more aggressive acceleration ramps, ie open the valve faster. 

The retainers accept factory locks (collets), which Toyota Heritage can supply if needed.

The original factory standard installed height will provide 38.6kg (85lb) on the valve seat. The table below gives all the data.

Can ship worldwide - no problems for overseas buyers.

Reproduction bespoke dash fascia to suit third generation Toyota Corolla E30 and E50 series models built between 1974 to 1981.

Suited to all E30 series and E50 series generation Corolla and Sprinter variants such KE30, KE35, KE38 an KE55 our dash fascias are made in Australia to the highest quality, 3D printed and can be configured (produced) to suit a wide range of instrumentation from OEM through to performance and electric-vehicle ('EV') conversion applications.

Instrumentation configurations are available for:

• Blank (no inset for instrumentation)
• Haltech IC7
• Racepack IQ3
• Motec C125/C185 and C127/C128
• AIM LINK MXP, MXS or MXG
• AEM ED7/CD7 or ED5/CD5
• Powertune 7"
• ECU Master ADU5 or ADU7
• Holley EFI 7"
• Fueltech FT450/FT550 and FT500/FT600

If your chosen instrumentation configuration is not listed above please email This email address is being protected from spambots. You need JavaScript enabled to view it.

OEM radio and air vents may be deleted and three different power plug configurations are also available - delete, USB or Narva 12V socket.

 Please use the drop down menus to select your dash fascia configuration.

 Available in either right hand drive or left hand drive - please use the additional drop down menu to select your driver side position.

Complete your 'third gen' Toyota Corolla project in style - whether its a retro-ride, drift car, track car, rally car, daily driver or restoration project.

Shipping worldwide weekly - no problems for overseas buyers.

Door card fastener clip pack to suit various Toyota models - Celica, Corolla, Corona, Supra, Hilux and Land Cruiser.

These clips are used to fasten side and rear door cards to the door.

These are a push in clip that have a fit to a 9mm hole and have a T1 13mm head diameter with a stem length of 14mm.

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica 

• AA63, GA61, RA60, RA61, RA63, RA64, RA65, SA60, SA63, TA60, TA61, TA63, TA64
• AT160, ST160, ST161, ST162, ST163, ST165 
• AT180, ST182, ST183, ST184 and ST185

Toyota Corolla

• KE30, KE35, KE36, KE38, TE31, TE37, TE38
• TE47
• KE50, KE55, TE51,
• AE70, AE71, CE70, CE71, CE72, KE70, KE71, KE72, KE73, KE74, TE70, TE71, TE72, TE73, TE74
• AE80, AE81, AE82, AE85, AE86, CE80, EE80

 Toyota Corona

• AT140, AT141, CT140, CT141, CT147, KT147, RT141, ST140, TT142, TT147, YT140

 Toyota Hilux

• LN50, LN51, LN55, LN56, LN57, RN50, RN55, RN58, YN50, YN51, YN52, YN55, YN56, YN57, YN58
  LN60, LN61, LN65, RN60, RN61, RN66, RN67, VZN61, VZN66, YN60, YN61G, YN61V, YN62, YN63, YN65, YN67
  RN70, RN75

 Toyota Supra

• MA61, MA63

Toyota Land Cruiser 

• BJ40, BJ41, BJ42, BJ44, BJ45, BJ46, FJ40, FJ45, HJ47
• BJ60, BJ61, FJ60, FJ61, FJ62, FJ62G, FJ62V, HJ60, HJ61
• BJ70, BJ71, BJ73, BJ74, BJ75, FJ70, FJ73, FJ75, HJ75, LJ75, LJ70, LJ71, LJ73, RJ70, RJ73 

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

Reproduction engine decal for Toyota models with 2T, 2T-B, 2T-C or 2T-G engines.

Suits 2T engined models as follows:

• Toyota Celica TA21, TA22
• Toyota Corolla TE21, TE27 and TE28
• Toyota Carina TA12, TA14, TA17, TA18, TA19V and TA30
• Toyota Corona TT100, TT106V, TT110 and TT120

Suits 2T-B engined models as follows:

• Toyota Celica TA28
• Toyota Corolla TE21, TE27 and TE28
• Toyota Carina TA12, TA14, TA17, TA18, TA19V and TA30

 Suits 2T-C engined models as follows:

• Toyota Celica TA21, TA22
• Toyota Corolla TE21, TE27 and TE28
• Toyota Carina TA12, TA14, TA17, TA18, TA19V and TA30

Suits 2T-G engined models as follows:

• Toyota Celica TA27 (1600GT versions)
• Toyota Corolla TE21, TE27 and TE28
• Toyota Carina TA12 and TA17 (1600GT versions)

These decals were fitted from the factory to the cam-shaft cover or the timing chain inspection plate for twin cam versions.

Select the decal for your engine by using the drop down menu.

Our reproduction decals are exacting in every detail. 

Shipping worldwide weekly - no problems for overseas buyers.

• 2T-B engine decal 2T-B engine decal
• 2T-C engine decal 2T-C engine decal
• 2T-G engine decal 2T-G engine decal
•  

Off the shelf and ready to go manifold flange kit that has been designed and engineered.

Make your own inlet and exhaust mainfolds with Toyota Heritage's stainless steel manifold flanges to suit your 3K or 4K high performance Toyota engine.

Our manifold flanges are made from 16mm stainless steel which is perfect for post-welding milling to ensure a flat and perfect fit to the engine head.

With both flanges made in the same material and thickness this ensures ease of even fastening of the manifolds to the engine head.

Select from Full Kit (incl both inlet and exhaust) or Exhaust Flange or Inlet Flange using the drop-down menu.

Perfect for the owner who is making their own ITB arrangement and needs an exhaust header to match.

Suitable for race, drift, road or any application. 

Made to order part.

Worldwide shipping weekly - so no problems for overseas buyers.

• Exhaust flange Exhaust flange
• Full Kit Full Kit
• Inlet flange Inlet flange
•  

Reproduction engine decal Toyota models with 'Cali-spec' 3K-C and 4K-C engines.

Suits the following Toyota vehicles fitted with a 3K-C or 4K-C engine:

• Toyota Corolla KE20 (North America only)
• Toyota Corolla KE30, KE35, KE38 and KE50 (Japan and Australia).
• Toyota Corolla KE70, KE72 and KE74 (Australia only)
• Toyota Starlet KP61 1981 to 1984

These decals were fitted to the top of the rocker cover from the factory to denote the installation of the mighty 3K-C or 4K-C engine.

Our reproduction part is exacting in every detail. 

Shipping worldwide weekly - no problems for overseas buyers.

This decal was applied to all Japanese built Toyota models throughout the late 1960's to 1980.

This included modesl such as Land Cruiser (FJ40, FJ45, FJ55 etc), Hilux (RN15, RN25 etc), Crown (MS55, MS60, MS70, MS80 etc), Celica (A20 series) and Corolla (E20 and E30 series).

Complete your classic Toyota Restoration in style with this decal that is applied to the top face of the radiator adjacent to the radiator cap.

Fitted at the very top of the radiator, this decal is most visible immediately when the bonnet (hood) is opened and provides that finishing touch to a resto.

Often the original decal may have been removed when the radiator was reconditioned, replaced or when a respray of the engine bay has taken place.

Available only from Toyota Heritage this decal will take your restoration one small step closer towards concourse.

We ship worldwide every week - no problems for international buyers.

Available for Toyota models with 2T-B engines and with one of two transmissions 

Suits 2T-B engined models as follows:

• Toyota Celica TA23, TA28, TA29 and TA60
• Toyota Corolla TE31 and TE37
• Toyota Carina TA12, TA14, TA17, TA18, TA19V, TA30, TA40, TA60 and TA61

You may find that your original plate is missing (these are not a VIN!) as an owner may have removed it for painting of sometimes they have corroded and are no longer legible.

The plate was used to inform the production line workers as to what model engine was to be fitted to the vehicle - part of Toyota's quality program!

Our reproduction part is exacting in every detail. 

The pricing includes having your car's data applied to the plate before we ship it to you.

Shipping worldwide weekly - no problems for overseas buyers.

Off the shelf and ready to go exhaust manifold flange that has been designed and engineered.

Make your own exhaust mainfold with this stainless steel flange to suit your 3K or 4K high performance Toyota engine.

This custom made flange is made from 16mm stainless steel which is perfect for post-welding milling to ensure a flat and perfect fit to the engine head.

Perfect for the owner who is making their own exhaust headers.

Suitable for race, drift, road or any application. 

Made to order part.

Worldwide shipping weekly - so no problems for overseas buyers.

Toyota Heritage recommends also looking at our listing for a complete kit (exhaust and inlet flanges) to ensure better overall fitment and improved purchase price.

Reproduction decal set for fluids (oil and water) to suit Toyota models with 3K and 4K engines of all variants.

Suits the following Toyota vehicles fitted with a 3K or 4K engine:

• Toyota Corolla KE30, KE35, KE38 and KE50 (Japan and Australia).
• Toyota Corolla KE70, KE72 and KE74 (Australia only)
• Toyota Starlet KP61 1981 to 1984

These decals were fitted to the top of the radiator cap, coolant overflow resevoir and the side of the rocker cover from the factory.

Our reproduction part is exacting in every detail. 

Shipping worldwide weekly - no problems for overseas buyers.

• Coolant level Coolant level
• Radiator cap Radiator cap
• Oils spec Oils spec
•  

Headlamp and grille (fender) fastener clip pack to suit various Toyota models - Celica, Corolla, Corona, Carina, Publica, Land Cruiser and Hilux

These clips are used to fasten inner guards (fenders) to the outer guard and are screwed into place. 

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica

• TA40, TA45, TA41, TA42, TA46, TA47, RA40, RA45, RA55, RA46, RA42 and RA43
• ST160, ST162, AT160, ST163, ST164 and ST165

Toyota Corolla

• KE10, KE11, KE15, KE16, KE17 and KE18
• KE20, KE25, TE21, TE25, TE27 and TE26
• KE30, KE35, KE50, KE55, TE31, TE51, KE36 and KE38
• TE72
• AE90, AE91, AE92 and EE90

 Toyota Land Cruiser

• FJ40, FJ45, FJ43, FJ47, BJ40, BJ42, BJ45, BJ43, BJ44, BJ47, HJ40, HJ45, HJ43 and HJ47

Toyota Publica 

• KP30, KP31, KP36V, KP37V, KP38, KP39 and KP50

 Toyota Carina

• TA10
• KA67
• ET176V, AT170, AT175, ST170, ST170G, CT170, CT170G and CT176V

Toyota Cressida

• TX30, RX30, RX32, RX35, MX30, MX35, MX40, MX41, MX45, MX32 and MX36
• TX67V, SX60, RX63, RX60, GX61, GX60G, GX61, MX61, MX62, MX63, LX60, LX67V and LX65

 Toyota Hilux and Toyota Surf

• All models to N190 series

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

Reproduction valve clearance decal for Toyota models with 2T-G and 2T-GR engines.

Suits 2T-G and 2T-GR  engined models as follows:

• Toyota Celica TA22, TA40, TA45, TA60 and TA61
• Toyota Corolla TE21, TE27, TE31, TE37, TE51 and TE71
• Toyota Carina TA12 and TA17

These decals were fitted to the air plenum from the factory and provided instructions for valve clearances and other data such as air filter element change out.

Our reproduction part is exacting in every detail. 

Shipping worldwide weekly - no problems for overseas buyers.

Off the shelf and ready to go inlet manifold flanges that have been designed and engineered.

Make your own inlet mainfolds with this stainless steel inlet flange kit to suit your 3K or 4K high performance Toyota engine.

This custom made inlet flange kit is made from 16mm stainless steel which is perfect for post-welding milling to ensure a flat and perfect fit to the engine head.

Perfect for the owner who is making their own ITB arrangement.

Suitable for race, drift, road or any application. 

Made to order part.

Worldwide shipping weekly - so no problems for overseas buyers.

Toyota Heritage recommends also looking at our listing for a complete kit (exhaust and inlet flanges) to ensure better overall fitment and improved purchase price.

Reproduction valve clearance decal for Toyota models with 2K, 3K-H, 3K-C or 4K-C engines.

Suits 4K-C ('California Spec') engined models as follows:

• Toyota Corolla KE50, KE55 and KE50R (Nov 1978 onwards)

Suits 3K-C ('California Spec') engined models as follows:

• Toyota Corolla KE30, KE35 and KE36
• Toyota Corolla KE50 (Japan only)
• Toyota Corolla KE20 (North America only)

Suits 3K-H ('High Octane Spec') engined models as follows:

• Toyota Corolla KE30 and KE36 (Japan only)
• Toyota Publica KP37 (Japan only)

Suits 2K engined models as follows:

• Toyota Publica KP30 and KE36 (also known as Toyota 1000)

These decals were fitted to rocker cover from the factory and provided instructions for valve clearances and other data such as air filter element change out.

Our reproduction part is exacting in every detail. 

Shipping worldwide weekly - no problems for overseas buyers.