Spare parts suitable for Toyota Crown S40 Series

Reproduction interior light dome lens suitable for your J50 series Toyota Land Cruiser, S40 Toyota Crown or T40 T50 series Corona.

These lenses are faithful reproductions made in Australia to the highest quality and replace original Koito part number L1804L (left side) and L1804R (right side).

These lenses has a diameter of approximately 120mm (4¾in) and are suited to the following models:

Toyota Land Cruiser

• FJ55, FJ55V and FJ56 - 1967 to 1978

Toyota Crown

• RS40, RS46, RS41, RS43 and RS45 - 1962 to 1967 
• MS40,MS46, MS41, MS43, MS45, MS45S - 1965 to 1966
• MS45B - 1967.

Toyota Corona

• RT40, RT43, RT46, RT47, RT50 and RT55 - 1964 to 1966 (early build third generation)

 These domes are faithful reproductions made in Australia to the highest quality and will complete your project in style - whether its a retro-ride, daily driver, restoration project or serious off-roader!

These dome lenses have been manufactured using precision tooling to produce a high quality faithful reproduction.

Shipping worldwide weekly - no problems for overseas buyers.

Complete your early Toyota restoration project!

These seals were fitted between the inside of the door frame and the window regulator/winder mechanism of Toyota's built during the 1960's and early 1970's. We have seen these on Crown, Corolla, Corona, Mark ii and Landcruiser just to name a few models.

These stop vibration and 'wobble' of your window winder handle and help eliminate rattles.

Our reproduction part is exacting in every detail.

All colours available from 1969 to 1971.

Complete your early Toyota restoration project in complete style!

These AMI Lustrelife paint colour decals were fitted in the engine bay of all early model Toyota's built during 1969 to 1971. These were applied to the Port Melbourne (Australia) assembled Crown, Corolla and Corona.

Our decals are correct in every detail including artwork, colour names and paint codes.

Colours used by AMI and included in our range of decals to chose from are:

• Apple
• Bronze Metallic
• Caribbean
• Cirrus Grey
• Columbine Blue
• Cornflower
• Cream
• Deep Russet
• Desert Beige
• Havana Gold
• Hayman Blue
• Marina Turquoise
• Midnight Blue
• Mocca
• Peak White
• Signal Red
• Sirius White
• Targa Pearl Metallic
• White 
• Willow

Often many cars have lost this decal when an owner has removed it for painting the original decal has been torn or lost.

If you cannot find your colour in the decals with have listed please contact us at Toyota Heritage.

We can also assist in identifying the colour of your car if you are unsure which decal to purchase.

These decals were also fitted to Rambler (Matador, Rebel, Hornet, American etc), Triumph (Herald, 2000, 2000PI, 2500TC etc) and AMC (Javelin, AMX etc). 

Complete your early Toyota restoration project in style with a Genuine Parts Warning decal.

These 'Genuine Parts Warning' decals were located on the aircleaner assembly or rocker cover of all early model Toyota's built during the 1960's and early 1970's at Australian Motor Industries (AMI). These decals were applied to the Port Melbourne (Australia) assembled Crown, Corolla and Corona.

Often many cars have lost this decal over their life as past owners may removed them for painting or the decal was simply torn or lost.

The decal advises buyers that genuine parts are made with the same quality as the originals and should always be used.

Completed on an original high chrome type material and using precision fonts this decal is an exact replica of those fitted back in the day.

Reproduction L1731 side marker lenses in amber suitable for K40 K100 series Toyota Stout, S40 series Toyota Crown and P40 P50 series Toyota Publica Starlet.

These lenses are faithful reproductions made in Australia to the highest quality and replace original Koito part number L1731.

These lenses are suited to the following models :

Toyota Stout (incl Lite Stout, Stout 1900, Stout 2000 and Stallion):

• RK41, RK43, RK45, RK47
  RK100.

Toyota Crown

• MS40,MS46, MS41, MS43, MS45, MS45S - 1965 to 1966
  MS45B - 1967

Toyota Publica and Starlet

• UP30, KP30, KP30S, KP31, UP36V, KP36V, KP37V, KP38, KP39
  KP40 and KP50

These lenses are also available in custom clear - please see our separate listing for clear lenses.

Complete your 'old school' Toyota project in style. Increasingly hard to find as NOS these reproduction lenses look great fitted to vintage restoration projects, well as retro rides or a 'shop truck'.

Shipping worldwide weekly - no problems for overseas buyers.

Complete your early Toyota restoration project in style with a pair of reproduction lenses to suit your early style factory Toyota Motor Corp auxiliary ('driving') lights.

Replaces original Koito part number L2589.

Mostly fitted to Toyota Stout and Toyota Land Cruiser these were also fitted as factory auxiliary driving lights on Crown, Corolla, Corona, Mark ii, and Hilux just to name a few other models.

You may find that your original lense is missing or cracked. These wonderful reproduction lenses are exacting in every detail. 

Shipping worldwide weekly - no problems for overseas buyers

All colours from 1969 to 1971 available.

Complete your early Toyota restoration project in complete style!

These AMI Lustrelife paint colour decals were fitted in the engine bay of all early model Toyota's built during 1969 to 1971. These were applied to the Port Melbourne (Australia) assembled Crown, Corolla and Corona.

Our decals are correct in every detail including artwork, colour names and paint codes.

Colours used by AMI and included in our range of decals to chose from are:

Often many cars have lost this decal when an owner has removed it for painting the original decal has been torn or lost.

If you cannot find your colour in the decals with have listed please contact us at Toyota Heritage.

We can also assist in identifying the colour of your car if you are unsure which decal to purchase.

These decals were also fitted to Rambler (Matador, Rebel, Hornet, American etc), Triumph (Herald, 2000, 2000PI, 2500TC etc) and AMC (Javelin, AMX etc). 

Complete your early Toyota restoration project with this reproduction AMI Build Plate.

These AMI Build Plates were fitted in the engine bay of all early model Toyota's built during the 1960's and early 1970's at the Australian Motor Industries Port Melbourne facility. Used extensively on Crown, Corolla, Corona and Tiara models they had a unique number that allowed AMI to keep track of the bodies it had built for Toyota.

Often many cars  have lost this plate or when an owner has removed it for painting the original plate has been deformed. Toyota Heritage's reproduction part is exacting in every detail. 

These AMI Build Plates compliment Toyota Heritage's reproduction TEQ Build plate and York Stock plate very nicely and adds that finishing touch to the engine bay of yoru early model Toyota for an authentic restoration.

The pricing includes having your car's unique build number applied to the plate before we ship it to you. 

Reproduction L1731 side marker lenses in clear suitable for K40 K100 series Toyota Stout, S40 series Toyota Crown and P40 P50 series Toyota Publica.

These lenses are faithful reproductions made in Australia to the highest quality and replace original Koito part number L1731.

These lenses are suited to the following models :

Toyota Stout (incl Lite Stout, Stout 1900, Stout 2000 and Stallion):

• RK41, RK43, RK45, RK47
  RK100.

Toyota Crown

• MS40,MS46, MS41, MS43, MS45, MS45S - 1965 to 1966
  MS45B - 1967

Toyota Publica and Starlet

• UP30, KP30, KP30S, KP31, UP36V, KP36V, KP37V, KP38, KP39
• KP40 and KP50

Complete your 'old school' Toyota project in style. Increasingly hard to find as NOS these reproduction lenses look great fitted to vintage restoration projects, well as retro rides or a 'shop truck'.

Shipping worldwide weekly - no problems for overseas buyers.

Complete your early Toyota restoration project in style with a reproduction Toyota (TEQ) Build Plate.

These TEQ Build Plates were fitted in the engine bay of all early model Toyota's built during the mid and late 1960's and early 1970's. Generally these were used up till December 1974, but this may vary in some countries.

We have seen these on Crown, Corolla, Corona, Mark ii, Stout, Publica, Hilux and Landcruiser just to name a few models.

You may find that your original plate is missing (these are not a VIN!) as an owner may have removed it for painting of sometimes they have corroded and are no longer legible.

The plate was used to inform the production line workers as to what model engine was to be fitted to the vehicle - part of Toyota's quality program!

Our reproduction part is exacting in every detail. We currently have one of these fitted to our Toyota Heritage KE17 race car and receive numerous compliments about how well this completes our car and the finish and standard of the plate itself.

The pricing includes having your car's data applied to the plate before we ship it to you.

We ship globally to all countries weekly.

All 1967 to 1968 colours available for Australian and New Zealand assembled Toyota models. Complete your early Toyota restoration project!

These AMI Lustrelife paint colour decals were located in the engine bay of all early model Toyota's built during the 1960's and early 1970's. These were applied to the Port Melbourne (Australia) assembled Crown, Corolla and Corona. Often many cars have lost this decal over their life as past owners may removed them for painting or the decal was simply torn or lost.

These decals were also fitted to Rambler (Matador, Rebel, Hornet, American etc), Triumph (Herald, 2000, 2000PI, 2500TC etc) and AMC (Javelin, AMX etc). They may have been fitted to Mercedes Benz and Volks Wagen in years prior to 1967.

This decal artwork (design) is completely correct for the 1967 and 1968 years and cover the AMI colour range 1967 to 1968, including the following:

• Desert Beige
• Glade Green
• Russet Metallic
• Safety Wattle
• Signal Red
• Silver Blue Metallic
• Silver Grey Metallic
• Vintage Wine
• White
• Willow

If you cannot find your colour in the decals we have listed please contact us at Toyota Heritage.

We can also assist in identifying the colour of your car if you are unsure which decal to purchase.

Reproduction valve clearance decal for Toyota models with 3R-B engines.

Suits models with 3R-B engines as follows:

• Toyota Crown RS30, RS31, RS32
• Toyota Crown RS40
• Toyota Stout RK100 (1964 - 1968)
• Toyota Bus RK170B
• Toyota Dyna RK170

These decals were fitted to the side of the rocker cover from the factory and provided data for valve clearances.

Our reproduction part is exacting in every detail. 

Shipping worldwide weekly - no problems for overseas buyers.

Suited to Toyota vehicles using four OEM wheel studs per hub.

Ensure good engineering practice with wheel studs that provide for proper engagement of wheel nuts with these longer than standard M12 1.5 pitch 72mm wheel studs.

Good engineering (safety) practice requires wheel nut engagement of the wheel stud to be the equivalent of the wheel stud diameter - 12mm for all Toyota models.

On a 1.5 pitch this means that your wheel nut must get at least 8 turns to ensure a safe and proper engagement.

Please check with us prior to purchase (This email address is being protected from spambots. You need JavaScript enabled to view it.) if your vehicle has been fitted with aftermarket hubs.

Toyota Heritage's long wheel stud kits provide enough length for proper engagement. Our open ended wheel nuts mean that they may also be used with a wide range of aftermarket and factory mag wheels.

Toyota Heritage offers four different wheel stud kits:

• Kit 1 - Wheel studs only
• Kit 2 - Wheel studs with wheel nuts suited to factory mag wheels
• Kit 3 - Wheel studs with wheel nuts suited to after market mag wheels
• Kit 4 - Wheel studs with wheel nuts suited to factory and after market mag wheels

Application:

Kit 1 (Stud Pack)

• 16 pieces (wheel studs) in the kit
• Perfect for when you have purchased after market mag wheels but you are not getting 8 turns of the wheel nuts the vendor supplied

Kit 2 (Factory Pack)

• 32 pieces in the kit including studs and open-end flat seat wheel nuts with captive washers
• Perfect for use with factory mag weels and using a wheel spacer up to 30mm to create offset to suit your handling set-up

Kit 3 (Aftermarket Pack)

• 32 pieces in the kit including studs and open-end tapered seat wheel nuts
• Perfect for use with almost any aftermarket mag wheel requiring a tapered seat wheel nut

Kit 4 (Track Pack)

• 48 pieces in the kit including studs and open-end tapered seat wheel nuts plus open-end flat seat wheel nuts with captive washers
• Perfect for the person who wants to run factory mag wheels around the streets and then switch to their track day wheels and tyres at the track

• Aftermarket Pack Aftermarket Pack
• Factory Pack Factory Pack
• Track Pack Track Pack
• Stud Pack Stud Pack
•  

Complete your early Toyota restoration project in style with a reproduction Toyota (TEQ) Build Plate for vehicles with original delivery in Japan.

These TEQ Build Plates were fitted in the engine bay of all early model Toyota's built during the mid and late 1960's and up to the year of 1970. Generally these were used up till December 1970, but this may vary on some models and for some cars sold in January 1971.

We have seen these on Crown, Corolla, Corona, Stout, Publica, and Landcruiser just to name a few models.

You may find that your original plate is missing (these are not a VIN!) as an owner may have removed it for painting of sometimes they have corroded and are no longer legible.

The plate was used to inform the production line workers as to what model engine was to be fitted to the vehicle - part of Toyota's quality program!

Our reproduction part is exacting in every detail. 

The pricing includes having your car's data applied to the plate before we ship it to you.

We ship globally to all countries weekly.

All 1965 to 1967 colours available for Australian and New Zealand assembled Toyota models. Complete your early Toyota restoration project!

These AMI Dulon E Type paint colour decals were located in the engine bay of all early model Toyota's built during the 1960's and early 1970's. These were applied to the Port Melbourne (Australia) assembled Crown, Corolla and Corona. Often many cars have lost this decal over their life as past owners may removed them for painting or the decal was simply torn or lost.

These decals were also fitted to Rambler (Classic, Ambassador, Matador, Rebel, Hornet, American etc), Triumph (Herald, Spitfire, 2000, 2000PI, 2500TC etc) and AMC (Javelin, AMX etc). They were also fitted to Mercedes Benz assembled in Australia.

This decal artwork (design) is completely correct for the 1965 and 1967 years. This is a two piece decal set and colours include the AMI colour range 1965 to 1967:

• Signal Red
• Surf Green
• Diplomatic Grey
• Executive Grey
• Sherwood Green
• Pearl White
• Forum Blue
• Pacific Blue
• Bahama Bronze

If you cannot find your colour in the decals we have listed please contact us at Toyota Heritage.

We can also assist in identifying the colour of your car if you are unsure which decal to purchase.

Reproduction valve clearance decal for Toyota models with 3R-B engines.

Suits models with 3R-B engines as follows:

• Toyota Crown RS30, RS31, RS32
• Toyota Crown RS40
• Toyota Stout RK100 (1964 - 1968)
• Toyota Bus RK170B
• Toyota Dyna RK170

These decals were fitted to the side of the rocker cover from the factory and provided data for valve clearances.

Our reproduction part is exacting in every detail. 

Shipping worldwide weekly - no problems for overseas buyers.

Complete your early Toyota restoration project with an authentic type York Motors Toyota dealership stock plate plate.

These Stock Plates were fitted in the engine bay of all early model Toyota's built during the 1960's and early 1970's. Used extensively on locally built AMI cars but also on fully imported models and this included Crown, Corolla, Sprinter, Corona, Mark ii, Tiara and Publica.

Often many cars that were sold through York Motors have lost this plate or when an owner has removed it for painting the original plate has been deformed.

Our reproduction part is exacting in every detail. We currently have one of these fitted to our Toyota Heritage KE17 race car and receive numerous compliments about how well this completes our car and the finish and standard of the plate itself.

Compliments our TEQ Build plate very nicely adding those finishing touches to the engine bay for an authentic restoration.

The pricing includes having your car's unique stock number applied to the plate before we ship it to you.

Complete your 'old school' Toyota project with this reproduction factory six row fuse box.

Complete with a cover that displays correct fuse allocation and TEQ logo, this suits all early model Toyota vehicles including:

• Landcruiser early BJ, HJ and FJ
• Crown MS40 RS40 series
• Corona RT40 series
• Publica
• Stout

This is high quality replacement product that will help your car's electrical system come back to life.

Bolts straight into most models and overcomes problems with broken fuse housings.

Worldwide shipping weekly - no problems for overseas buyers.

All 1965 to 1967 colours available for Australian and New Zealand assembled Toyota models. Complete your early Toyota restoration project!

These AMI Dulon E Type paint colour decals were located in the engine bay of all early model Toyota's built during the 1960's and early 1970's. These were applied to the Port Melbourne (Australia) assembled Crown, Corolla and Corona. Often many cars have lost this decal over their life as past owners may removed them for painting or the decal was simply torn or lost.

These decals were also fitted to Rambler (Classic, Ambassador, Matador, Rebel, Hornet, American etc), Triumph (Herald, Spitfire, 2000, 2000PI, 2500TC etc) and AMC (Javelin, AMX etc). They were also fitted to Mercedes Benz assembled in Australia.

This decal artwork (design) is completely correct for the 1965 and 1967 years. This is a two piece decal set and colours include the AMI colour range 1965 to 1967:

• Taupe
• Deep Taupe
• Surf Green
• Glade Green
• Tasman Turquoise
• Signal Red
• Diplomatic Grey
• Executive Grey
• Black
• White
• Cover Blue
• Elm Green
• Pearl White

If you cannot find your colour in the decals we have listed please contact us at Toyota Heritage.

We can also assist in identifying the colour of your car if you are unsure which decal to purchase.

Genuine Eagle brand 9mm ignition leads to suit your Toyota Crown fitted with an M or 2M engine.

Our photo shows each of the boot and tube assemblies specific to this kit that suits the M and 2M engines.

Suits 2.0L M SOHC Crown models as follows:

• MS41, MS45, MS46 and MS47

Suits 2.3L 2M SOHC Crown models as follows:

• MS45B
• MS53, MS55 and MS57

General description:

 A premium quality ignition lead set specifically designed as an upmarket replacement for OHC motors fitted with Boot and Tube component technology.

Being Eliminator series, they are fitted with 1300 ohms per metre Ferrite Spiral Core conductor which by induction design delivers peak voltage to the plugs ensuring almost complete combustion for super quick starts and smooth running.

Tested to ISO 3808 Standards.

Features - Boot & Tube Assembly Features*

• Hi-temp Silicone Well Cover boot
• PVT insulator tube insulates plug terminal to prevent high voltage crossover
• Hi-temp Silicone Tip Seal.

Terminal Features

• High Memory spring steel retaining clip for positive terminal locking at all RPM'S.
• Extra long .51mm base offers minimal heat transfer from plug tip to inner conductor. This ensures maximum cable life.
• Triple cable retaining ribs and "W" shaped crimp ensure superior cable retention.

 Cable Features

• Simply "the best" Stainless Steel wound Ferrite coated Spiral Core conductor yields ultra low resistance ensuring peak voltage delivery to the spark plugs.
• High Dielectric Silicone inner jacket.
• Technologically advanced nylon tape adds tensile strength.
• 260°C High Temp. modified Silicone outer jacket ensures complete protection against heat and engine bay contaminants.

Shipping wordlwide weekly - no problems for overseas buyers.