Bonnet (hood) insulation fastener clip pack to suit various Toyota models - Celica, Supra, and Soarer

These clips are used to fasten the bonnet (hood) insulation into place.

These are a push in fastener that has a gloss black 30mm head and 15mm lenth that fits to an 8mm hole.

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica 

• ST182, ST183 and ST184
• ST204 and ST205

Toyota Soarer

• GZ20

 Toyota Supra

• GA70, JZA70 and MA70

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

Door card, side trim panel and fascia fastener clip pack to suit various Toyota models - Caldina, Celica, Corolla, Corona, Supra, MR2, Soarer, Prado, Yaris, Hilux and Land Cruiser.

These clips are used to fasten side and rear door cards to the door as well as other interior trim and fascia panels.

These are a push in clip that have a fit to a 9mm hole size and measure 12.8mm ( top head diameter), 15.6mm (centre head diameter) , 17.7mm (bottom head diameter) with a stem length of 14.2mm.

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Caldina

• AT191, CT190, CT196, CT197, CT198, CT199, CT216, ET196, ST190, ST191, ST195, ST198
• AT211, ST210, ST215

 Toyota Celica 

• ST200, ST202, ST203, ST204 and ST205

Toyota Corolla

• AE91, AE92, AE95, CE90, EE90
• AE100, AE101, AE102, AE103, AE104, CE100, CE101, CE104, EE100, EE101
• AE110, AE111, AE112, AE114, AE115, CDE110, CE110, CE113, CE114, CE116, EE110, EE111, WZE110, ZZE111, ZZE112
• CDE120, ZRE120, ZZE120, ZZE121, ZZE122 and ZZE123

 Toyota Corona

• YT140

 Toyota Hilux

• KDN145, LN140, LN141, LN145, LN147, RZN142, RZN144, RZN147, RZN148, RZN149
• KDN150, KDN151, LN150, LN152,
• KDN165, KDN166, KZN165, LN166, LN167
• KDN170, LN170, LN171, LN172, RZN173, RZN174, VZN172
• KDN190, KZN190, LN192 and RZN194

  Toyota Supra

• MA61, MA63

Toyota Land Cruiser 

• BJ60, FJ62, HJ60
• BJ73, FJ70, FJ73, FJ75, FZJ70, FZJ71, FZJ73, FZJ74, FZJ75, FZJ78, FZJ79, HDJ78, HDJ79, HJ75, HZJ70, HZJ71, HZJ73, HZJ74, HZJ75, HZJ76, HZJ77, HZJ78, HZJ79, KZJ70, KZJ71, KZJ73, KZJ77, KZJ78, LJ70, LJ71, LJ72, LJ73, LJ77, LJ78, LJ79, PZJ70, PZJ73, PZJ75, PZJ77, RJ70, RJ73, RJ77
• FJ80, FZJ80, HDJ80, HDJ81, HZJ80, HZJ81
• FZJ100, FZJ105, HDJ100, HDJ101, HZJ105 and UZJ100

Toyota Prado

• KDJ90, KDJ95, KZJ90, KZJ95, LJ90, LJ95, RZJ90, RZJ95, VZJ90 and VZJ95

Toyota MR2 

• SW20 and SW21

Toyota Soarer

• JZZ30, UZZ30, UZZ31 and UZZ32

Toyota Supra

• JZA80

Toyota Yaris 

• NCP10, NCP11, NCP12, NCP13, NLP10, SCP10
• NCP20
• EP80, EP81, EP82, EP85, NP80
• EP90, EP91, EP95 and NP90

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

Front and rear floor carpet set for your S40 series Toyota Crown ute (aka Pick-up).

Suited to all RHD Toyota Crown S40 series utes or pick-ups such as RS46 and MS46 built between 1962 to 1967 our carpet floor mats are patterened off the floor of our an original S40 Crown, are well fitting and made in Australia to the highest quality with a non-slip foam backing.

Add a little comfort and luxury to your second generation Toyota Crown ute - these utes had rubber floor coverings and while that's most suited to their utilitarian work horse origins, long drives to car shows and club runs can be done with some extra comfort when you add some nice period correct looking carpet floor mats.

There are two mats in the set that are placed in the two front foot well. 

Displayed here in classic 1960's brown plush pile with brown edge binding, these mats provide a look that has an OEM look and feel.

Available in loop or plush pile and fourteen different colours. Just use the drop down menus to select pile and colour.

You can also select your edge binding colour - please also use the drop down menu to select your colour of choice.

NOTE: Colour swatches shown are on plush pile carpet and may differ slightly on loop.

Complete your 'second gen' Toyota Crown S40 series project in style - whether its a daily driver or restoration project.

Shipping worldwide weekly - no problems for overseas buyers.

• Edge binding colours Edge binding colours
• 
•  

• Bark Bark
• Black Black
• Blue Blue
• Brown Brown
• Buckskin Buckskin
• Burgundy Burgundy
• Charcoal Charcoal
• Chevy Chevy
• Ginger Ginger
• Green Green
• Kingfisher Kingfisher
• Red Red
• Slate Slate
• Spindrift Spindrift
•  

Floor mat set for the passenger area of your left hand drive fifth generation E80 series Toyota Corolla Sprinter.

Suited to all LHD lift back Toyota Corolla Sprinter AE85 or AE86 built between 1983 to 1987 our carpet floor mats are well fitting and made in Australia to the highest quality with a non-slip foam backing. 

These mats are patterned from original OEM mats and are available in loop or plush pile and fourteen different colours. Just use the drop down menus to select pile and colour.

You can also select the colour of yoru edge binding - simply use the drop down menu to select the colour you like.

NOTE: Colour swatches shown are on plush pile carpet and may differ slightly on loop.

Complete your 'fifth gen' Toyota Corolla Sprinter project in style - whether its a retro-ride, drift car, daily driver or restoration project.

Shipping worldwide weekly - no problems for overseas buyers.

• Edge binding colours Edge binding colours
• 
•  

• Bark Bark
• Black Black
• Blue Blue
• Brown Brown
• Buckskin Buckskin
• Burgundy Burgundy
• Charcoal Charcoal
• Chevy Chevy
• Ginger Ginger
• Green Green
• Kingfisher Kingfisher
• Red Red
• Slate Slate
• Spindrift Spindrift
•  

Improve handling and performance of your first generation ZN6 series Toyota 86 (GT86) with a custom front and rear Sway Bar just like those used in the Toyota 86 Racing Series.

Toyota Heritage's sway bars are Australian made, two-way adjustable (front) and three-way adjustable (rear) and are powder coated to the highest standards.

The standard size front sway bar we offer for the ZN6 Series Toyota 86 (GT86) is 20mm finished in red powder coat. Ideal for street and track with increased torsional stiffness over factory sized bars.

The standard size rear sway bar we offer for the ZN6 Series Toyota 86 (GT86) is 18mm finished in red powder coat. Ideal for street and track with increased torsional stiffness over factory sized bars.

Our ZN6 Series Toyota 86 (GT86) sway bar kit comes complete with bushes, brackets, links and lateral locks.

We offer the opportunity for buyers to customise their sway bar set by selecting the size required in the drop down menu 'Sway Bar Size'.

Buyers can select their desired sway bar thickness of 20mm or 22mm for the front bar and buyers can select their desired sway bar thickness for the rear bar starting at 18mm and up to 24mm.

We ship worldwide weekly - no problems for overseas buyers.

Improve handling and performance of your first generation XV40 series Toyota Aurion with a custom front and rear Sway Bar just like those used on Highway Patrol cars.

Toyota Heritage's sway bars are Australian made, two-way adjustable (front) and two-way adjustable (rear) and are powder coated to the highest standards.

The standard size front sway bar we offer for the XV40 series Toyota Aurion is 27mm finished in red powder coat. Ideal for street and track with increased torsional stiffness over factory sized bars.

The standard size rear sway bar we offer for the XV40 series Toyota Aurion is 20mm finished in red powder coat. Ideal for street and track with increased torsional stiffness over factory sized bars.

Our XV40 series Toyota Aurion sway bar kit comes complete with bushes, brackets, links and lateral locks.

We ship worldwide weekly - no problems for overseas buyers.

Reproduction valve clearance decal for Toyota models with 4M engines.

Suits models with 4M engines as follows:

• Toyota Crown MS45B
• Toyota Crown MS50, MS51, MS52, MS53, MS56
• Toyota Crown MS64, MS67
• Toyota Mark ii MX12, MX22, MX28

These decals were fitted to the side of the rocker cover from the factory and provided data for valve clearances.

Our reproduction part is exacting in every detail. 

Shipping worldwide weekly - no problems for overseas buyers.

Reproduction valve clearance decal for Toyota models with 4M engines.

Suits models with 4M engines as follows:

• Toyota Crown MS65, MS68V, MS75
• Toyota Crown MS80, MS90, MS100
• Toyota Mark ii MX12, MX22, MX28, MX32, MX36

These decals were fitted to the side of the rocker cover from the factory and provided data for valve clearances.

Our reproduction part is exacting in every detail. 

Shipping worldwide weekly - no problems for overseas buyers.